Sagola DPC™ Cup System: Faster Color Changes, Less Cleaner – How to Choose & Use 100–800 ml (125/190 µm)
When the color changes in the booth, every minute counts. The Sagola DPC™ Disposable Paint Cup System is designed to make color changes faster and reduce cleaning effort – featuring a stable ABS outer cup solution, disposable liner, domed lid with integrated filter, locking ring (collar), and sealing plugs for temporary storage.
What you will confidently decide after this guide
- Which cup size (100–800 ml) fits your job (Spot Repair up to 4+ panels).
- When a 125 µm vs. 190 µm filter makes sense (as a practical guide).
- How to set up, use, store, and dispose of the system – clean & reproducible.
Note: Representative image (DPC100).
Product Overview: Sizes, Typical Uses & Filters
According to manufacturer documentation, the system is available in 100–800 ml. The sizes are intended as orientation based on job scope (Spot Repair up to 4+ panels). Filters are integrated (including 125 µm and 190 µm). Please understand these values/assignments as practical guidelines; the final choice depends on the material and painting process.
| Variant | Typical Use (Guideline) | Filter (Integrated) | Practical Advantage |
|---|---|---|---|
| 100 ml | Spot Repairs | 125 µm / 190 µm | Minimizes material waste, quick preparation |
| 200 ml | 1–2 Panel Repairs | 125 µm / 190 µm | All-rounder for smaller repairs |
| 400 ml | 2–3 Panel Repairs | 125 µm / 190 µm | Good standard for many jobs |
| 600 ml | 3–4 Panel Repairs | 125 µm / 190 µm | More reserve, less frequent mixing |
| 800 ml | 4+ Panel Repairs | 125 µm / 190 µm | For larger surfaces & longer spray times |
CTA: Order Popular Sets Directly
Three frequently chosen sizes – select according to your job scope and filter requirements:
Recommended Basic Settings (Guidelines)
Manufacturer documentation emphasizes measuring/mixing aids on the cup and the integrated filter – specific pressure/nozzle numbers are not given as universally valid values. Use these points as guidelines and also refer to the data sheets for the paint and spray gun:
- Mixing: Mix directly in the cup using the markings/mixing aids; follow the paint manufacturer's specifications.
- Filter Selection: 125 µm typically for finer filtration; 190 µm for higher throughput – depending on material/process.
- Cup Size: Choose based on job scope (Spot Repair up to 4+ panels) as a pragmatic orientation.
- Temporary Storage: During breaks, insert the plug and store upside down to keep the filter wetted.
Professional Workflow (5–7 Steps)
- Prepare Cup: Provide the ABS outer cup and insert the matching liner.
- Fill & Mix: Pour in paint/material and mix according to specifications – markings on the cup help with this.
- Set Lid/Filter: Place the domed lid with integrated filter on top.
- Close Collar: Tighten the locking ring (integrated gasket ensures a clean fit).
- Attach Adapter: Use the appropriate adapter to connect the system to the spray gun.
- Spray: Paint as usual – when changing colors, replace the liner/lid instead of intensively cleaning the cup.
- Breaks/Residual Material: Insert plug and store upside down; then continue working or dispose of material professionally.
Troubleshooting (4 Typical Problems)
- Check if the lid/filter is seated correctly and the collar is properly tightened.
- For thicker materials, check the filter variant and material specifications (filtration/flow are material-dependent).
- During pauses: Use the plug and store upside down so the filter does not dry out.
- Remove the collar, check sealing surfaces, and reattach cleanly.
- Is the liner inserted correctly? Kinks at the edge can interfere with the seal.
- Check the adapter connection for a secure fit.
- Reinsert the liner and press it evenly into the cup.
- Seat the lid/filter correctly so the liner can operate "cleanly."
- Check material specifications (viscosity can influence behavior).
- Prepare sets/components (liner/lid) in advance so the change is done in one move.
- Keep outer cup/adapter as a constant "base" – only replace consumables.
- Temporarily store residual material with a plug instead of mixing new paint (if process-permitted).
Maintenance & Handling (5 Points)
- Clean Outer Cup: Compared to classic gravity cups, cleaning effort is reduced – however, keep sealing surfaces clean.
- Check Collar/Gasket: Look for damage/residue to ensure it remains leak-proof.
- Maintain Adapter: Keep the connection clean, check for a secure fit (Twist-Lock/Connector).
- Correct Storage: Use the plug and store upside down to keep the filter wetted.
- Disposal According to Regulations: Observe the paint manufacturer's safety data sheet; allow liners to dry according to protocol or dispose of in suitable containers.
FAQ (Practical Questions)
Many workshops use 400 ml as a good all-round guideline; the documentation categorizes sizes by job scope (Spot Repair up to 4+ panels).
The filter is integrated into the lid and designed as a full-diameter filter – this is intended for consistent paint flow.
Yes, a sealing plug is provided for this purpose. Storing upside down helps keep the filter moist (if your process permits).
There are adapters for Sagola guns and other manufacturers/threads. Check the thread of your gun and select the appropriate adapter.
The documentation does not provide blanket pressure values for all applications. Use the paint and gun data sheets as the authoritative basis.
Conclusion
The Sagola DPC™ cup system is a practical solution if you want to speed up color changes and reduce cleaning effort – without the stress of decanting, with mixing aids on the cup and plug storage. Choose your cup size according to job scope and filter according to material/process – and then pick the matching set.
