Northshield® Disposable Coverall "PAINT PRO": Clean Work with Paint, Dust & Spray Mist
Anyone spraying, sanding, or working in maintenance/cleaning needs protection that fits, breathes, and reliably shields clothing. The white-blue Northshield® "PAINT PRO" is designed as a disposable protective suit with microporous lamination for typical stresses such as spray mist and particles.
Product image (example view). Details per variant in the shop.
What is the "PAINT PRO" suitable for in practice?
This disposable coverall was developed for typical tasks involving spraying and painting as well as sanding work – wherever dust, fine dust, or spray mist can occur. Additionally, it is intended for cleaning or maintenance activities where clean protection over work clothing is beneficial.
Product Overview: Variants, Applications, Advantages
| Variant | Typical Uses | Features & Advantages | Link |
|---|---|---|---|
| S | Painting, sanding, maintenance/cleaning | Hood, front zipper, elastic cuffs, breathable | View S |
| M | Painting, sanding, maintenance/cleaning | Lint-free/antistatic, ventilated back area | View M |
| L | Spray painting work, sanding dust | Microporous lamination, high wearing comfort, secure fit | View L |
| XL | Painting/sanding, maintenance in industry/trade | Elastic cuffs on arm/waist/leg, freedom of movement | View XL |
| 2XL | Spray mist/dust during larger movements | Breathable, antistatic, hood & zipper | View 2XL |
| 3XL | Painting/sanding, trade/industry | Very high comfort due to lightweight, skin-friendly material | View 3XL |
Note: Protection classification applies to the product; the correct size depends on body measurements and desired range of motion.
Recommended Basic Settings (Guidelines)
| Parameter | Guideline / Recommendation | Why it helps |
|---|---|---|
| Size | Choose according to body measurements (see table below). For lots of movement, favor "comfortable" over "tight." | Better freedom of movement with simultaneous secure fit through elastic zones. |
| Cuff Fit | Place elastic cuffs on arm/waist/legs flat; overlap gloves/shoes cleanly. | Reduces the risk of dust/spray mist "seeping under." |
| Hood | Position the hood so that mask/goggles fit tightly (without tension). | More comfort, less friction – especially during longer tasks. |
"Basic settings" are consciously formulated as practical guidelines here because they depend on the activity, underclothing, and PPE combination.
Size Guide: Find the Right Fit Quickly
| Size | Clothing Size | Height (cm) | Chest Circumference (cm) | Waist Circumference (cm) |
|---|---|---|---|---|
| S | 42/44 | 165–168 | 84–88 | 74–78 |
| M | 46/48 | 171–174 | 92–96 | 82–86 |
| L | 50/52 | 177–180 | 100–104 | 90–94 |
| XL | 54/56 | 182–184 | 108–112 | 98–104 |
| 2XL | 58/60 | 186–188 | 116–120 | 110–116 |
| 3XL | 62/64 | 190–192 | 124–128 | 122–126 |
Tip: If you are between two sizes, decide based on use: more movement (e.g., frequent bending) → larger; precise work (less movement) → closer to measurements.
Pro Workflow: 6 Steps for Clean Dressing & Working
- Prepare Workplace: Lay out coverall, open zipper, fold hood back.
- Check Forearms/Legs: Choose gloves and shoes/overshoes so that cuffs overlap cleanly.
- Dressing Bottom to Top: Step into legs, pull coverall up, then arms; place elastic zones flat.
- Close Zipper: Close front zipper completely, briefly check fit at waist/legs.
- Position Hood: Align hood so that mask/goggles don't slip and you have a clear view.
- During Work: Schedule short breaks during heavy sweating/stress – the ventilated back helps, but doesn't replace break logic.
Troubleshooting: 4 Typical Problems & Quick Solutions
- Check size based on measurements (height/chest/waist) – choose next size up if necessary.
- Readjust elastic waist/leg cuffs so the fabric doesn't "pull up."
- Place microfiber cuffs flat at the wrists, then put gloves over them (or under, depending on process).
- Test range of motion: do a few squats/raise arms – only then start.
- Plan short breaks + change coveralls (disposable logic).
- Adjust underclothing (moisture management) to maintain comfort.
- Check if zipper is fully closed and cuffs are snug at arm/waist/legs.
- Optimize overlaps (gloves/shoes) – a common weak point for dust/spray mist.
Maintenance & Handling (Disposable Practice)
- Store dry, clean, and protected so the microporous lamination is not damaged.
- Brief visual inspection before use: zipper, cuffs, material (no tears).
- Remove with low contamination after use (do not brush outside against face/inner clothing).
- Disposal according to operational specifications (depending on substance/dust class).
- For serial work: Define replacement rhythm (e.g., per shift/job) – depending on contamination and process.
Technical Quick Facts (from Product Info)
- Material: Microporous lamination made of polypropylene
- Features: Hood, front zipper, microfiber cuffs at the wrists
- Properties: Breathable, lint-free, antistatic
- Certifications (Product side): EN ISO 13982-1:2004 (Type 5B), EN ISO 13034:2005 (Type 6B), EN 1149-5:2008 (antistatic)
- Color: White-Blue
FAQ: Common Practical Questions
Order the Right Size Now
Choose the variant that fits your measurements and your daily work routine:
Conclusion
The Northshield® Disposable Coverall "PAINT PRO" is a practical choice if you are looking for a protective suit with Type 5B/6B alignment, hood/front zipper, elastic cuffs, and a ventilated back zone for painting, sanding, or maintenance work. The right size is crucial for everyday use – then the suit fits securely and you work cleanly and comfortably.
