The Elcometer 510 Adhesion Gauge accurately measures the adhesive force between the coating and substrate. Elcometer 510 Automatic Pull-Off Adhesion Gauge Features Explained: Automatic adhesion tester with selectable pull rates for 10, 14.2, 20 and 50mm diameter stamps.Display trend graphs or live statistics next to the measurement value.Individual, user-defined pull rate graphs can be stored with each measurement. Store individual readings and pull rate plots in up to 2,500 alphanumeric batches, complete with date, time and fracture patterns.Pull either to maximum or to pre-set threshold. Unique holding mechanisms allow you to set a time delay before releasing pressure to zero.Store cohesion and adhesion failure images with your tear-off force data in accordance with national and international standards. Accurate Fully adjustable test rates from 0.1-1.4 MPa/s (14.5-203 psi)Accuracy ±1% of full scaleCan be used in accordance with national and international standardsSelectable units: MPa, psi, Nmm² and N High performanceSmooth pressure generation up to 100 MPa (14,400 psi)USB and Bluetooth® data output to iOS1 or Android™ devicesStores up to 60,000 readings in 2,500 batches EfficientIdeal for use in the laboratory and on siteReusable stamps with 10, 14.2, 20 and 50mm (0.39, 0.56, 0.76 and 1.96") diameterCompatible with ElcoMaster® and ElcoMaster® mobile appMeasures on small, curved and flat surfaces SummaryThe Elcometer 510 Adhesion Tester applies smooth, continuous pressure using an automatic hydraulic pump, giving consistent and repeatable test results. Whilst the pull rate on most adhesion testers is set manually, the Elcometer 510 Adhesion Tester allows the user to select the desired pull rate, which is then automatically applied by the tester.The Elcometer 510 Adhesion Gauge has all the features you would expect from a product designed and manufactured by Elcometer, including ease of use, a robust and ergonomic design, a menu-driven colour display, and user-selectable statistics and display modes.The Elcometer 510 Adhesion Tester not only reduces inspection time, but also speeds up the process of generating test reports. Users can immediately review their data usingthe freeElcoMaster® data management software when working in the field or at their own premises. With the push of a button, each live reading can be transferredvia Bluetooth® to a PC or mobile device, enabling users to create professional reports. DurableSealed, robust and impact resistantSealed, rugged and impact-resistantDust and water resistant to IP64 ReliableRepeatability and reproducibility2-year warranty on the measuring devicelot date and time signature SimpleSupplied in a rugged plastic case for easy transportData output via USB andBluetooth® to iPhone or Android™Heller LCD colour screen

The Elcometer PTG range offers all the features and functions required to accurately measure the thickness of virtually any material. AccurateHighly accurate measurement of thin materialsElcometer PTG gauges are easy to use and have a measurement range of 0.15mm (0.006") to 25.40mm (1,000") with an accuracy of up to ±1% across three measurement modes: Interface-Echo (IE), Echo-Echo (EE) and Plastic (PLAS). PowerfulStorage of measured values for further evaluationUp to 100,000 measured values can be stored in the memory of the measuring device while you are measuring. They can then be downloaded to an inspection application or ElcoMaster® for further analysis and reporting. Wireless connectionConnect wirelessly to any PC, Android™ or iOS mobile device.Connect the Elcometer PTG8 via Bluetooth® or USB to a PC, Android™ or iOS mobile device and download the data into an inspection application or ElcoMaster® for instant reporting. Features:Measurement modes: Interface-Echo (I-E), Echo-Echo (E-E) and Plastic Mode (PLAS)Measuring range from 0.15mm (0.006") to 25.40mm (1.000")Calibration options: 2-point, 1-point, material, sound velocity and factory calibrationThree user-definable calibration memoriesUser-definable measurement rate: 4, 8 and 16 measurements per secondUser-selectable measurement resolution: 0.1mm (0.01") or 0.01mm (0.001")Scan modeMeasured values, selected statistics, bar chart, history chart, B-scan and difference modeDevice memory for up to 100,000 measured values in up to 1,000 sequence or grid batchesUser-definable lower and upper limit values with audible and visual pass/fail warningUSB and Bluetooth® data output to ElcoMaster® and ElcoMaster® Mobile App

Suitable probe handles for the Elcometer 266 High Voltage Porosity Tester can be found HERE.__________________________________________________________________The revolutionary Elcometer 266 High Voltage DC Coating Porosity Detector makes testing coatings safer, easier and more reliable than ever before.Easy to useThe voltage selector automatically sets the correct voltage for your coating thickness reading. No need for reference tables. SafeA double safety switch on the handle prevents accidental switch-on and special ribs provide excellent protection. VersatileSelect a different handle to change the voltage: 5kV, 15kV or 30kV DC, or 30kV DC continuous voltage. Suitable for testing porosity in coatings up to 7.5mm (300 mils) thick, the Elcometer 266 Holiday Detector is the ideal solution for inspecting coatings on pipework as well as other protective coatings.This device's integrated voltage calculator sets the correct voltage based on the test standard and the thickness of the material being tested. A fully automatic voltage calculation selects the correct test voltage depending on the coating thickness.Selectable test voltage:0.5kV to 1kV in 50V steps1kV to 30kV in 100V stepsA double safety switch on the handle to prevent unintentional switching on (only grey/orange probe handles)Built-in voltmeter/voltage detector ensures that the test voltage always corresponds to the selected voltage.Visual and audible alarm: bright LED's on the probe handle and a loud buzzer clearly indicate when a pore has been detectedTo change the maximum voltage range, use a different handle: 5 kV, 15 kV or 30 kV DC or 30 kV DC constantA wide range of brush and rolling spring probes are available Elcometer 266 DC Holiday Detector Features Explained Voltage CalculatorThe voltage calculator automatically sets the correct voltage based on the coating thickness entered. No need for comparison charts thanks to the integrated voltage calculation. Simply enter the test standard and coating thickness and the device automatically programmes the correct voltage. Adjustable voltage Voltage setting via the keyboard – no screwdriver required 0.5 kV - 1 kV in 50 V steps 1 kV - 30 kV in 100 V steps. Voltage setting via the keyboard – no screwdriver required. The current sensitivity can be preset manually or set automatically by the test instrument for partially conductive coatings. Internal voltmeter/jeep tester Internal voltmeter/jeep tester ensures that the selected voltage corresponds to the test voltage. An internal calibrated jeep tester and closed loop circuit ensure accurate measurement and continuous regulation of the generated test voltage, regardless of climatic conditions. Interchangeable probe handlesInterchangeable probe handles: 500-5,000 volts, 500-15,000 volts, 500-30,000 volts Audible and visual alarmsAudible and visual alarm when a fault is detected. Bright LEDs on the handle and a loud audible signal clearly indicate when the test device is switched on (red) and when a sparkover is detected (blue). Battery packBattery packs that can be charged inside or outside the test instrument for continuous use. The battery packs can be charged either inside or outside the device. The batteries are fully charged in 4 hours and provide 40 hours of continuous use. Universal Probe AdaptorEnables all the main accessories to be used with the Elcometer 266. Screen displayLarge display with backlight, making it easy to read in dark environments. If a defect is detected, the backlight will also flash. Second HandleThe optional second handle is designed for two-handed use without compromising safety. Particularly suitable for testing pipework and tank floors. Safety feature Double safety switch on the handle to prevent unintentional switching on. A 2-stage safety switch ensures automatic switch-off if the handle is not held.Special ribs for better protection and an optional second handle for two-handed use. The longer insulating ribs protect the user and are specifically designed to meet the requirements of the EN61010 standard. High-voltage testing has never been safer.The loudspeaker in the test device emits a ticking sound to clearly indicate that the handle is live.When a sparkover is detected, a loud audible alarm sounds. The volume of the alarm signal is adjustable to ensure that it can be heard in noisy environments.

The Elcometer 456 Coating Thickness Gauge is available with an integral probe. It is ideal for one-handed use and provides consistent, repeatable and accurate results. AccurateAccurate measurements on smooth, rough, thin and curved surfacesWith a measurement accuracy of ±1% and increased measurement resolution, the Elcometer 456 delivers accurate, temperature-stable measurements every time. SimpleCalibrated and ready to useEasy to use menus, large buttons and colour LCD screen with automatic image rotation; factory calibrated and ready to use. PowerfulStores up to 150,000 measurements in 2,500 batchesMeasure coatings up to 13mm (500mil) thick on metal substrates and output data via USB and Bluetooth® to ElcoMaster®. The Elcometer 456 Dry Film Thickness Gauge is available in three different models. Each gauge offers the user advanced functionality from the entry level Elcometer 456 Model B to the top of the range Elcometer 456 Model T.The integrated coating thickness gauges are ideal for single-handed operation as the large footprint of the internal Bigfoot™ probe provides greater stability during coating thickness measurement, enabling consistent, repeatable and accurate dry film thickness results.Separate coating thickness gauge models offer even greater flexibility in dry film thickness measurement with their wide range of probes.Compatible with ElcoMaster® software and ElcoMaster® Mobile App; individual coating thickness readings can be transferred via USB or Bluetooth® to a PC or mobile device for analysis and instant reporting. Key features RuggedWear resistant and suitable for use in harsh environmentsThe sealed 456 is wear and impact resistant, dust and water resistant to IP64 and suitable for use in harsh environments. ReliableCarefree useRepeatable, reproducible and with a 2-year1 manufacturer's warranty.

All Elcometer 456 probes are fully interchangeable to meet your specific requirements and are available in a range of styles and scale ranges.Ferrous probes (F)Ferrous probes measure non-magnetic coatings on ferromagnetic substrates.Elcometer 456 ferrous gauges are compatible with any ferrous probe. Non-ferrous metal probes (N)Non-ferrous probes measure non-conductive coatings on non-ferrous substrates.Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe. FNF combination probesFNF combination probes measure on both ferrous and non-ferrous metals with automatic substrate detection.Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. High temperatureElcometer probes have a maximum operating temperature of 80°C (176°F)*.Separate Elcometer iron probes have a maximum operating temperature of 150°C (300°F)*.High temperature PINIP™ have a maximum operating temperature of 250°C (480°F)*.* The specified temperature is the background temperature and the probe operating time must be reduced to ensure minimal temperature build-up in the probe. Ferrous probes measure non-magnetic coatings on ferromagnetic substrates. Elcometer 456 ferrous gauges are compatible with any ferrous probe.Non-ferrous probes measure non-conductive coatings on non-ferrous substrates. Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe.FNF combination probes measure on both ferrous and non-ferrous metals with automatic substrate detection. Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. Key featuresStraight Standard straight probeStandard probes measure coatings on flat and curved surfaces.Anodised probeChemical-resistant and washable for use in anodising. Mini probesMini probes are ideal for hard-to-reach areas and edges.Waterproof probesSealed for use under water, can also be used with diving gloves. Soft coating probesProbes for large areas are designed for soft materials (HVCA approval).Probes for thick coatingsIdeal for measuring coatings up to 31 mm thick. Scan probes Standard scan probeFor fast scanning of large areas without damaging the probe or the surface.Ball bearing scan probe*Clampable adapter for large coated structures, coarse coatings or primers used in prefabrication. Angled probes Right-angled probesFor recording measured values in areas with little free space.Right-angled mini probeFor measuring coatings on edges, thin pipes or small surfaces. Telescopic probesTelescopic probes for hard-to-reach areas.45° angle probeFor measuring areas that are difficult to access or have complex shapes. PINIP™ probes (for attaching) Integrated PINIP™ probeConverts a measuring device with separate probe into an integrated measuring device ideal for one-handed useHigh temperature PINIP™For measuring coatings on ferrous metal substrates at up to 250 °C (480 °F). Probes with armoured cable F / FNF Armoured probeReinforced, wear-resistant cables reduce the risk of cable damage.

The Elcometer 121 paint thickness testers are used to test the thickness of single or multi-layer paint coatings and are available in two model variants. The colour coating tester is available in two versions, Standard and Top:Standard colour coating testers can be used for microscopic coating inspections and destructive measurements of coating thickness.Top colour coating testers offer the same functionality as the standard version and can also be used for cross-cut adhesion tests with optional tools. Main featuresCompact and practical, ideal for measuring paint thickness where space is at a premiumMade from anodised aluminium for a long service lifeIntegrated microscope with 50x magnification and rotating scaleBright white LED light source for clear viewing through the microscopeThe standard colour coating tester offers a single cutting tool and integrated storage space for 3 cutting toolsThe cutting tools of the top-of-the-range colour coating testers are mounted on a rotating tool holder in the body of the tester, allowing a quick change from one test to the next.test to the next is possibleThe tool holder of the top model offers space for three cutting tools as well as an optional cross-cut tool

Material Thickness Material Thickness Gauges Wall Thickness Gauges Ultrasonic Gauges Ultrasonic Testers The Elcometer Ultrasonic Material Thickness Gauge range offers all the features and functions to measure material thickness and sonic velocity on virtually any material in a wide variety of applications. IntelligentUser definable limits for pass/fail indicationUsers can set lower and upper limits with audible and visual pass/fail alerts. Limits can be set for individual readings or for each batch. AccurateA range of calibration options for accuracy and efficiencyMTG meters offer a range of calibration options, including one-point calibration. Users can also select one of 39 pre-set materials stored in the device or store up to three calibrations in memory. VersatileMeasurement of coated and uncoated surfacesThe flexible and easy-to-use Elcometer MTG range not only measures uncoated surfaces, but can also measure coated surfaces. In Echo-Echo-ThruPaint™ (EE) mode, coatings up to 2 mm (80 mil) thick are ignored. Material thickness Material thickness gauges Wall thickness gauges Ultrasonic gauges Ultrasonic testersAutomatic probe recognition ensures that the correct probe is recognised when changing the measuring headScan mode with 16Hz - ideal for measuring large areasUser-selectable measurement resolution: 0.1mm (0.01") or 0.01mm (0.001")Measurement modes: Pulse-Echo (PE), Echo-Echo ThruPaint™ and Velocity of Sound (VM)Upper and lower limit indicators indicate problem areasSome MTG measuring devices are only supplied as a measuring device. Measuring heads must be ordered separatelyIntegrated zero disc ensures maximum accuracyStores up to 100,000 readings in up to 1,000 sequential batchesSelectable measuring speed of 4, 8, 16 Hz (4, 8, 16 readings per second)

All Elcometer 456 probes are fully interchangeable to meet your specific requirements and are available in a range of styles and scale ranges.Ferrous probes (F)Ferrous probes measure non-magnetic coatings on ferromagnetic substrates.Elcometer 456 ferrous gauges are compatible with any ferrous probe. Non-ferrous metal probes (N)Non-ferrous probes measure non-conductive coatings on non-ferrous substrates.Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe. FNF combination probesFNF combination probes measure on both ferrous and non-ferrous metals with automatic substrate detection.Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. High temperatureElcometer probes have a maximum operating temperature of 80°C (176°F)*.Separate Elcometer iron probes have a maximum operating temperature of 150°C (300°F)*.High temperature PINIP™ have a maximum operating temperature of 250°C (480°F)*.* The specified temperature is the underground temperature and the probe operating time must be reduced to ensure minimum temperature build-up in the probe. Ferrous probes measure non-magnetic coatings on ferromagnetic substrates. Elcometer 456 ferrous gauges are compatible with any ferrous probe.Non-ferrous probes measure non-conductive coatings on non-ferrous substrates. Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe.FNF combination probes measure on both ferrous and non-ferrous metals with automatic substrate detection. Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. Key featuresStraight Standard straight probeStandard probes measure coatings on flat and curved surfaces.Anodised probeChemical-resistant and washable for use in anodising. Mini probesMini probes are ideal for hard-to-reach areas and edges.Waterproof probesSealed for use under water, can also be used with diving gloves. Soft coating probesProbes for large areas are designed for soft materials (HVCA approval).Probes for thick coatingsIdeal for measuring coatings up to 31 mm thick. Scan probes Standard scan probeFor fast scanning of large areas without damaging the probe or the surface.Ball bearing scan probe*Clampable adapter for large coated structures, coarse coatings or primers used in prefabrication. Angled probes Right-angled probesFor recording measured values in areas with little free space.Right-angled mini probeFor measuring coatings on edges, thin pipes or small surfaces. Telescopic probesTelescopic probes for hard-to-reach areas.45° angle probeFor measuring areas that are difficult to access or have complex shapes. PINIP™ probes (for attaching) Integrated PINIP™ probeConverts a measuring device with separate probe into an integrated measuring device ideal for one-handed useHigh temperature PINIP™For measuring coatings on ferrous metal substrates at up to 250 °C (480 °F). Probes with armoured cable F / FNF Armoured probeReinforced, wear-resistant cables reduce the risk of cable damage.

All Elcometer 456 probes are fully interchangeable to meet your specific needs and are available in a range of designs and scale ranges.Ferrous (F)Iron gauges are used to measure non-magnetic coatings on iron-magnetic substrates.Elcometer 456 iron gauges are compatible with any iron probe. Non-ferrous metal probes (N)Non-ferrous probes measure non-conductive coatings on non-ferrous substrates.Elcometer 456 Non-Ferrous gauges are compatible with any non-ferrous probe. FNF Combination ProbesFNF combination probes measure both ferrous and non-ferrous metals with automatic substrate recognition.The Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. High TemperatureElcometer probes have a maximum operating temperature of 80°C (176°F)*.Separate Elcometer ferrous probes have a maximum operating temperature of 150°C (300°F)*.High Temperature PINIP™ have a maximum operating temperature of 250°C (480°F)*.* The temperature given is the substrate temperature and the time of use of the probe must be reduced to ensure a minimum temperature rise in the probe. Ferrous probes measure non-magnetic coatings on ferrous substrates. The Elcometer 456 Ferrous gauges are compatible with any ferrous probe.Non-ferrous probes measure non-conductive coatings on non-ferrous substrates. Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe.FNF combination probes measure both ferrous and non-ferrous metals with automatic background detection. Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. Key FeaturesStraight Straight Standard ProbeStandard probes measure coatings on flat and curved surfaces.Anodising probeChemically resistant and washable for use in anodising. Mini probesMini probes are ideal for hard-to-reach places and edges.Waterproof probesSealed for underwater use, can also be used with diving gloves. Soft coating probesProbes for large areas are designed for soft materials (HVCA approved).Thick Coating ProbesIdeal for measuring coatings up to 31mm thick. Scan Probes Standard Scan ProbeFor quickly scanning large areas without damaging the probe or surface.Ball-bearing scan probe*Clamp-on adapters for large coated structures, coarse coatings or primers used in prefabrication. Angle probes Right-Angle ProbesFor collecting readings in areas with limited clearance.Right-Angle Mini ProbeFor measuring coatings on edges, thin tubes or small areas. Telescopic probesTelescopic probes for hard-to-reach areas.45° angle probeFor measuring areas that are difficult to access or have complex shapes. PINIP™ (plug-in) probes Integrated PINIP™ probeConverts a separate probe meter into an integrated meter ideal for one-handed use.High Temperature PINIPFor measuring coatings on ferrous substrates at temperatures up to 250°C (480°F). Probes with armoured cable F / FNF Armoured probeReinforced, abrasion-resistant cables reduce the risk of cable damage.

All Elcometer 456 probes are fully interchangeable to meet your specific requirements and are available in a range of styles and scale ranges.Ferrous probes (F)Ferrous probes measure non-magnetic coatings on ferromagnetic substrates.Elcometer 456 ferrous gauges are compatible with any ferrous probe. Non-ferrous metal probes (N)Non-ferrous probes measure non-conductive coatings on non-ferrous substrates.Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe. FNF combination probesFNF combination probes measure on both ferrous and non-ferrous metals with automatic substrate detection.Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. High temperatureElcometer probes have a maximum operating temperature of 80°C (176°F)*.Separate Elcometer iron probes have a maximum operating temperature of 150°C (300°F)*.High temperature PINIP™ have a maximum operating temperature of 250°C (480°F)*.* The specified temperature is the background temperature and the probe operating time must be reduced to ensure minimal temperature build-up in the probe. Ferrous probes measure non-magnetic coatings on ferromagnetic substrates. Elcometer 456 ferrous gauges are compatible with any ferrous probe.Non-ferrous probes measure non-conductive coatings on non-ferrous substrates. Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe.FNF combination probes measure on both ferrous and non-ferrous metal with automatic substrate detection. Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. Key featuresStraight Standard straight probeStandard probes measure coatings on flat and curved surfaces.Anodised probeChemical-resistant and washable for use in anodising. Mini probesMini probes are ideal for hard-to-reach areas and edges.Waterproof probesSealed for use under water, can also be used with diving gloves. Soft coating probesProbes for large areas are designed for soft materials (HVCA approval).Probes for thick coatingsIdeal for measuring coatings up to 31 mm thick. Scan probes Standard scan probeFor fast scanning of large areas without damaging the probe or the surface.Ball bearing scan probe*Clampable adapter for large coated structures, coarse coatings or primers used in prefabrication. Angled probes Right-angled probesFor recording measured values in areas with little free space.Right-angled mini probeFor measuring coatings on edges, thin pipes or small surfaces. Telescopic probesTelescopic probes for hard-to-reach areas.45° angle probeFor measuring areas that are difficult to access or have complex shapes. PINIP™ probes (for attaching) Integrated PINIP™ probeConverts a measuring device with separate probe into an integrated measuring device ideal for one-handed useHigh temperature PINIP™For measuring coatings on ferrous metal substrates at up to 250 °C (480 °F). Probes with armoured cable F / FNF Armoured probeReinforced, wear-resistant cables reduce the risk of cable damage.

This revolutionary Elcometer 266 high voltage DC detector makes porosity testing of coatings safer, easier and more reliable than ever before.User friendlyThe voltage calculator automatically sets the correct voltage for your coating thickness value. No need for reference tables. SafeA double safety switch on the handle prevents accidental switch-on and special ribs provide excellent protection. VersatileChoose a different handle to change the voltage: 5kV, 15kV or 30kV DC, or 30 kV DC continuous voltage. Suitable for testing the porosity of coatings up to 7.5 mm (300 mils) thick, the Elcometer 266 Holiday detector is the ideal solution for inspecting coatings on pipework and other protective coatings.The integrated tension calculator of this device sets the correct tension based on the test standard and the thickness of the material to be tested. A fully automatic voltage calculation selects the correct test voltage depending on the coating thicknessSelectable test voltage:0.5kV to 1kV in 50V steps1kV to 30kV in 100V stepsA double safety switch on the handle to prevent unintentional activation (only grey/orange probe handles)An integrated voltmeter / voltage tester ensures that the test voltage always corresponds to the selected voltageVisual and audible alarm: Bright LEDs on the probe handle and a loud buzzer clearly indicate when a pore has been detectedTo change the maximum voltage range, use a different handle: 5 kV, 15 kV or 30 kV DC or 30 kV DC constantA wide range of brush and roller spring probes are available Explanation of the features of the Elcometer 266 DC Holiday Detector Voltage CalculatorThe voltage calculator automatically sets the correct voltage based on the coating thickness entered. No need for comparison tables thanks to the inbuilt voltage calculator. Enter the test standard and coating thickness and the unit will automatically programme the correct voltage. Adjustable tension Voltage setting via the keypad - no screwdriver required 0.5 kV - 1 kV in 50 V increments 1 kV - 30 kV in 100 V increments. Voltage can be set via the keypad, so no screwdriver is required. The current sensitivity can be preset manually or set automatically by the tester for partially conductive coatings. Internal voltmeter/jeep tester Internal voltmeter/jeep tester ensures that the selected voltage corresponds to the test voltage. An internal calibrated jeep tester and closed loop control ensure accurate measurement and continuous regulation of the generated test voltage regardless of climatic conditions. Interchangeable probe handlesInterchangeable probe handles: 500 - 5,000 volts, 500 - 15,000 volts, 500 - 30,000 volts Audible and visual alarmsAudible and visual alarm when defects are detected. Brightly lit LEDs on the handle and a loud audible signal clearly indicate that the tester is switched on (red) and when a spark is detected (blue). Battery packRechargeable battery packs can be charged inside and outside the tester for continuous use. The battery packs can be charged either inside or outside the device. The batteries are fully charged in 4 hours and allow 40 hours of continuous use. Universal probe adapterAllows all major accessories to be used with the Elcometer 266. Screen displayLarge backlit display that is easy to read even in dark environments. If a fault is detected, the backlight also flashes. Second handleThe optional second handle is designed for two-handed use without compromising safety. Particularly suitable for checking pipework and tank bottoms. Safety feature Double safety switch on the handle to prevent unintentional switch-on. A 2-stage safety switch ensures automatic switch-off if the handle is not held.Special ribs for better protection and optional second handle for ambidextrous use The longer insulating ribs protect the user and are specifically designed to fulfil the requirements of the EN61010 standard. High voltage testing has never been safer.The loudspeaker in the tester emits ticking noises and clearly indicates that the handle is live.If a spark is detected, a loud acoustic alarm is emitted. The volume of the alarm signal can be adjusted to ensure that it is audible even in noisy environments.

The Elcometer 141 Paint Inspection Gauge (PIG) provides a reliable method for destructive coating thickness testing on both single and multi-layer coatings. It is ideal for use on metallic and non-metallic substrates such as wood, glass and plastic.Large, easy-to-hold handle – even thick and hard coatings can be cut easilyInternal storage compartment for cutting bladesMicroscope with 50x magnification Scale range0 to 1.8mm (0 to 0.07") scale resolution0.02mm (0.001") Dimensions (with handle attached)160 x 100 x 35mm (6.3 x 4 x 1.4") Weight (with handle fitted)510g (1lb 2oz)

All Elcometer 456 probes are fully interchangeable to meet your specific requirements and are available in a range of styles and scale ranges.Ferrous probes (F)Ferrous probes measure non-magnetic coatings on ferromagnetic substrates.Elcometer 456 ferrous gauges are compatible with any ferrous probe. Non-ferrous metal probes (N)Non-ferrous probes measure non-conductive coatings on non-ferrous substrates.Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe. FNF combination probesFNF combination probes measure on both ferrous and non-ferrous metals with automatic substrate detection.Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. High temperatureElcometer probes have a maximum operating temperature of 80°C (176°F)*.Separate Elcometer iron probes have a maximum operating temperature of 150°C (300°F)*.High temperature PINIP™ have a maximum operating temperature of 250°C (480°F)*.* The specified temperature is the underground temperature and the probe operating time must be reduced to ensure minimal temperature build-up in the probe. Ferrous probes measure non-magnetic coatings on ferromagnetic substrates. Elcometer 456 ferrous gauges are compatible with any ferrous probe.Non-ferrous probes measure non-conductive coatings on non-ferrous substrates. Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe.FNF combination probes measure on both ferrous and non-ferrous metal with automatic substrate detection. Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. Key featuresStraight Standard straight probeStandard probes measure coatings on flat and curved surfaces.Anodised probeChemical-resistant and washable for use in anodising. Mini probesMini probes are ideal for hard-to-reach areas and edges.Waterproof probesSealed for use under water, can also be used with diving gloves. Soft coating probesProbes for large areas are designed for soft materials (HVCA approval).Probes for thick coatingsIdeal for measuring coatings up to 31 mm thick. Scan probes Standard scan probeFor fast scanning of large areas without damaging the probe or the surface.Ball bearing scan probe*Clampable adapter for large coated structures, coarse coatings or primers used in prefabrication. Angled probes Right-angled probesFor recording measured values in areas with little free space.Right-angled mini probeFor measuring coatings on edges, thin pipes or small surfaces. Telescopic probesTelescopic probes for hard-to-reach areas.45° angle probeFor measuring areas that are difficult to access or have complex shapes. PINIP™ probes (for attaching) Integrated PINIP™ probeConverts a measuring device with separate probe into an integrated measuring device ideal for one-handed useHigh temperature PINIP™For measuring coatings on ferrous metal substrates at up to 250 °C (480 °F). Probes with armoured cable F / FNF Armoured probeReinforced, wear-resistant cables reduce the risk of cable damage.

The robust Elcometer 319 Dew Point Meter is designed to measure and record all relevant climate parameters required to determine the appropriate conditions for colour coating. AccurateComplies with ISO 8502-4Each meter is supplied with a calibration certificateMeasured value display switchable between degrees Celsius and degrees FahrenheitAll readings are stored with a date and time signature SimpleEasy-to-use, menu-guided, multilingual user interfaceEasy-to-read illuminated display for up to five user-defined parametersArrow symbols for parameter trend display FlexibleAn integrated K-probe connection allows surface temperature measurement during remote monitoring with a separate probeWith an external probe, the thermometer mode converts the device into a thermometer - ideal for measuring the temperature before applying the coatingMeasurement hold function for capturing and checking manual readings before savingCan be used as a handheld measuring device or as a data logger for remote monitoring1Limit values can be defined for each measurement. The device triggers a visual and audible alarm if these are exceeded Measurement and recording of climate parameters:Relative humidityAir temperatureSurface temperatureDew pointTΔ (difference between surface temperature and dew point)Dry bulb temperatureWet bulb temperatureExternal surface probe (type K)Specific humidity DurableAvailable with a 2-year manufacturer's warranty1Safe to use in ambient temperatures between -20°C (-4°F) and +80°C (+176°F)Water and dust protection to IP66Revised sensors with robust and ergonomic design offer greater wear resistance for longer durabilityEach meter can be powered either by two AA batteries (for up to 4003 hours of use) or via the USB cableGauges can be re-certified at authorised Elcometer Service Centres PowerfulConnect the Elcometer 319 via Bluetooth® or USB to a PC, Android™ or iOS smartphone and transfer the data to inspection software or ElcoMaster® for instant reporting.Fast respondingThe device calculates the time available for data recording when using batches

The Elcometer 510 Adhesion Gauge accurately measures the adhesive force between the coating and substrate. Elcometer 510 Automatic Pull-Off Adhesion Gauge Features Explained: Automatic adhesion tester with selectable pull rates for 10, 14.2, 20 and 50mm diameter stamps.Display trend graphs or live statistics next to the measurement value.Individual, user-defined pull rate graphs can be stored with each measurement. Store individual readings and pull rate plots in up to 2,500 alphanumeric batches, complete with date, time and fracture patterns.Pull either to maximum or to pre-set threshold. Unique holding mechanisms allow you to set a time delay before releasing pressure to zero.Store cohesion and adhesion failure images with your tear-off force data in accordance with national and international standards. AccurateFully adjustable test rates from 0.1-1.4 MPa/s (14.5-203 psi)Accuracy ±1% of full scaleCan be used in accordance with national and international standardsSelectable units: MPa, psi, Nmm² and N High performanceSmooth pressure generation up to 100 MPa (14,400 psi)USB and Bluetooth® data output to iOS1 or Android™ devicesStores up to 60,000 readings in 2,500 batches EfficientIdeal for use in the laboratory and on siteReusable stamps with 10, 14.2, 20 and 50mm (0.39, 0.56, 0.76 and 1.96") diameterCompatible with ElcoMaster® and ElcoMaster® mobile appMeasures on small, curved and flat surfaces SummaryThe Elcometer 510 Adhesion Tester applies smooth, continuous pressure using an automatic hydraulic pump, giving consistent and repeatable test results. Whilst the pull rate on most adhesion testers is set manually, the Elcometer 510 Adhesion Tester allows the user to select the desired pull rate, which is then automatically applied by the tester.The Elcometer 510 Adhesion Gauge has all the features you would expect from a product designed and manufactured by Elcometer, including ease of use, a robust and ergonomic design, a menu-driven colour display, and user-selectable statistics and display modes.The Elcometer 510 Adhesion Tester not only reduces inspection time, but also speeds up the process of generating test reports. Users can immediately review their data usingthe freeElcoMaster® data management software when working in the field or at their own premises. With the push of a button, each live reading can be transferredvia Bluetooth® to a PC or mobile device, enabling users to create professional reports. DurableSealed, robust and impact resistantSealed, rugged and impact-resistantDust and water resistant to IP64 ReliableRepeatability and reproducibility2-year warranty on the measuring devicelot date and time signature SimpleSupplied in a rugged plastic case for easy transportData output via USB andBluetooth® to iPhone or Android™Heller LCD colour screen

All Elcometer 456 probes are fully interchangeable to meet your specific needs and are available in a range of designs and scale ranges.Ferrous (F)Iron gauges are used to measure non-magnetic coatings on iron-magnetic substrates.Elcometer 456 iron gauges are compatible with any iron probe. Non-ferrous metal probes (N)Non-ferrous probes measure non-conductive coatings on non-ferrous substrates.Elcometer 456 Non-Ferrous gauges are compatible with any non-ferrous probe. FNF Combination ProbesFNF combination probes measure both ferrous and non-ferrous metals with automatic substrate recognition.The Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. High TemperatureElcometer probes have a maximum operating temperature of 80°C (176°F)*.Separate Elcometer ferrous probes have a maximum operating temperature of 150°C (300°F)*.High Temperature PINIP™ have a maximum operating temperature of 250°C (480°F)*.* The temperature given is the substrate temperature and the time of use of the probe must be reduced to ensure a minimum temperature rise in the probe. Ferrous probes measure non-magnetic coatings on ferrous substrates. The Elcometer 456 Ferrous gauges are compatible with any ferrous probe.Non-ferrous probes measure non-conductive coatings on non-ferrous substrates. Elcometer 456 non-ferrous gauges are compatible with any non-ferrous probe.FNF combination probes measure both ferrous and non-ferrous metals with automatic background detection. Elcometer 456 FNF gauges are compatible with all ferrous, non-ferrous and FNF combination probes. Key FeaturesStraight Straight Standard ProbeStandard probes measure coatings on flat and curved surfaces.Anodising probeChemically resistant and washable for use in anodising. Mini probesMini probes are ideal for hard-to-reach places and edges.Waterproof probesSealed for underwater use, can also be used with diving gloves. Soft coating probesProbes for large areas are designed for soft materials (HVCA approved).Thick Coating ProbesIdeal for measuring coatings up to 31mm thick. Scan Probes Standard Scan ProbeFor quickly scanning large areas without damaging the probe or surface.Ball-bearing scan probe*Clamp-on adapters for large coated structures, coarse coatings or primers used in prefabrication. Angle probes Right-Angle ProbesFor collecting readings in areas with limited clearance.Right-Angle Mini ProbeFor measuring coatings on edges, thin tubes or small areas. Telescopic probesTelescopic probes for hard-to-reach areas.45° angle probeFor measuring areas that are difficult to access or have complex shapes. PINIP™ (plug-in) probes Integrated PINIP™ probeConverts a separate probe meter into an integrated meter ideal for one-handed use.High Temperature PINIPFor measuring coatings on ferrous substrates at temperatures up to 250°C (480°F). Probes with armoured cable F / FNF Armoured probeReinforced, abrasion-resistant cables reduce the risk of cable damage.

Elcometer 456 for separate iron and non-ferrous probes, model B A simple and intuitive to use gauge for quick and precise measurement of coatings on metal substrates. For separate probes for measuring non-magnetic coatings on magnetic metal (F) and non-conductive coatings on non-magnetic metal (NF). The separate F, NF or FNF probes must be ordered separately! Sampling rate of more than 70 measurements per minute. Rotatable, large, high-contrast 2.4" (6cm) TFT colour display. Robust, shock-resistant and dust-tight casing. User-friendly menu in over 25 selectable languages with graphical display of important functions (e.g. calibration). Several calibration methods can be selected (smooth, rough, etc.). Statistics functions. Integrated emergency light. Further features and properties such as technical data, see data sheet. Elcometer 456 Coating Thickness Gauge with Separate Probe The Elcometer 456 Coating Thickness Gauge is available with a wide range of interchangeable probes, offering greater flexibility when measuring the thickness of coatings on metallic substrates. Advantages Measurements of coatings up to 31mm (1.220mil) thick on metal substrates Easy-to-read, customisable display with automatic brightness control Ergonomic design, ideal for continuous use Dust and water protected to IP64 Temperature-stable layer thickness measurements Fast It helps you work more efficiently 70+ readings per minute and 140+ per minute with scan probe, multiple calibration memory and alphanumeric batch identification. Accurate Accurate measurements on smooth, rough, thin and curved surfaces Measures on smooth, rough, thin and curved surfaces with an accuracy of ±1% according to national and international standards. Simple large buttons and colour LCD screen with automatic image rotation; factory-calibrated with upper and lower limit indicators; multilingual. Reliable Robust design: durable, impact resistant and with fully traceable test certificates and our 2-year gauge warranty.Elcometer 456 gauges are protected against manufacturing defects by a one-year warranty. The warranty can be extended to two years free of charge at www.elcometer.com within 60 days of the date of purchase. High-performance Stores up to 150,000 readings in 2,500 batches. Measures coatings up to 31mm (1.220mils) thick on metal substrates and outputs data via USB and Bluetooth® to ElcoMaster®. Using the Scan Probe in Scan Mode Using the Elcometer 456 in scan mode can significantly reduce inspection time when measuring dry film thickness without affecting the accuracy: Drag the scanning probe across the entire surface to be measured. When the probe is lifted from the surface, the gauge displays the average, maximum and minimum coating thickness. Each set of three readings (average, maximum and minimum) can be displayed on the historical graph and stored in memory. During each scan, the Elcometer 456 displays the live thickness reading along with an analogue bar graph showing the thickness relative to both the nominal thickness and user-defined limits (if set). Using the scanning probe in repeat mode When the ultrasonic probe is dragged across the coated surface in Repeat Auto* mode, a reading is taken approximately every half a second. Each individual reading is stored in the memory. With a data logging rate of more than 140 readings per minute, the repeat function can significantly speed up dry film inspection of large coated areas.

Elcometer dual element transducers are designed for ultrasonic material thickness measurement when only one side of the material to be tested is accessible. Dual element transducersDual element material thickness gauges are ideal for inspecting metal substrates, but can also measure other materials such as plastics, composites or fibreglass. Frequency and diameter discsMeasuring heads can be selected according to the frequency and size of the crystal. The frequency of a measuring head is determined by the type of material and the intended thickness range. The choice of crystal size depends on the accessibility, shape and surface characteristics of the object to be measured. Each measuring head can be easily identified by the disc at the top. Explanation of the two-element probe characteristicsWhen using the Echo-Echo ThruPaint™ (E-E) measurement mode, high damped dual element coating thickness transducers, designated HD/CT, are required. Highly damped CT coating thickness gauges also enable simultaneous coating and material thickness measurement in conjunction with selected gauge models.Special measuring heads are available for thickness measurement on high-temperature surfaces.

The Elcometer 270 Series utilises the wet sponge method for pore detection and sets a new standard in this class of instrument. The Elcometer 270 is a high quality tester that operates at low voltage and utilises similar accessories to high voltage testers.Ready to use straight out of the boxAutomatic sensitivity calibration and voltage testBattery charge level indicatorVisual and audible alarmIntegrated and separate probeLarge selection of interchangeable probe accessoriesTangle-free cable with quick disconnectLarge standard spongeOne inspection kit available for all your needs

Cross-cut device 6 teeth x 1 mm. Robust, heavy-duty cross-cut tool for quick testing of adhesive strength. Easy to change blades, non-slip handle, can be extended with the Elcometer 141 P.I.G.

Cross-cut tester with 6 cutting edges at 1 mm intervals, cutting drum with 4 cutting edges, additional 4 cutting edges can be used by turning the drum, anodised aluminium handle with pressure roller

ISO cross-cut set complete 6 teeth x 2 mm. Robust, heavy-duty cross-cut device for quick testing of adhesive strength. Easy to change blades, non-slip handle, can be extended with the Elcometer 141 P.I.G.

Cross-cut tester 6 teeth x 2 mm. Sturdy, heavy cross-cut tester for quick testing of adhesion. Easily replaceable blades, non-slip handle, can be combined with the Elcometer 141 P.I.G.

Cross-cut device 11 teeth x 1.5 mm. Robust, heavy-duty cross-cut tool for quick testing of adhesive strength. Easy to change blades, non-slip handle, can be extended with the Elcometer 141 P.I.G.

Cross-cut device 11 teeth x 1 mm. Robust, heavy-duty cross-cut tool for quick adhesion testing. Easy to change blades, non-slip handle, can be extended with the Elcometer 141 P.I.G.

Cross-cut device 6 teeth x 3 mm. Robust, heavy-duty cross-cut tool for quick adhesion testing. Easy to change blades, non-slip handle, can be extended with the Elcometer 141 P.I.G.

Elcometer has developed a viscous gel for use on horizontal and vertical surfaces.Common couplant is used over a temperature range of -15 to 104°C (5 to 220°F). The Elcometer high temperature gel has a range of up to 398°C (750°F) for use with high temperature probes.

Each single-element probe is supplied with 9mm and 12mm acrylic delay lines suitable for measurements on steel, aluminium and titanium.When measuring thinner plastics in PLAS (Plastic) mode, a graphite delay line must be used. These are available separately as accessories.